Diode Dynamics Accessory Wiring Harness Install Guide

If you have ever wanted to add parking light triggered accessories to your vehicle without worrying about overloading an existing circuit, a dedicated relay harness is the right tool for the job. In this guide we walk through the complete accessory wiring harness installation from Diode Dynamics, covering the relay basics, the ground and positive connections, the output wires, the ttap signal connection, and the optional LED switch setup. We tested and followed along with this harness ourselves, so we can break down exactly how each wire goes where and why.

Video courtesy of Diode Dynamics

What Is in the Kit

The kit is refreshingly simple. You get the accessory harness itself along with one connector that is included, and that is all you need to run the basic setup. If you selected the switch option, you also get the switch wiring plus the actual LED switch in the color you chose. We appreciate that Diode Dynamics keeps the parts count low because it makes the whole install approachable for anyone who is doing this for the first time.

Before you start, it helps to understand the bigger picture of how these systems work. If you are brand new to this topic, our rundown of relay harness installation basics is a good primer that explains when and why you want a relay in the first place.

How the Relay System Works

This harness is built off of a relay system, and relays are great because they provide a reliable source of power in a very safe way. The whole point is that you are not drawing too much power from any other accessories on the vehicle. The base of the system is the relay itself. Relays work by taking a major power source in and sending it out to the connected components when another, smaller power source such as a parking light or other small 12 volt signal is activated. In other words, that tiny signal relays into a bigger signal that actually drives your accessories.

This is exactly why we like running accessories off a dedicated relay harness instead of tapping a bunch of loads straight into a factory circuit. The relay isolates the heavy current draw and routes it directly from the battery, so your small trigger wire only ever handles a light signal load.

Connecting the Ground Wire

The first connection to make is the ground wire. You can see there is an O-ring connector on the end, and it is a black wire. This can be connected to your negative battery terminal or any good metal part of the vehicle’s body. A solid ground is critical for the relay to function reliably, so take a moment to make sure your chosen point is clean bare metal if you are not going straight to the battery.

Ground wire with O-ring connector on accessory wiring harness
The black ground wire connects to the battery negative terminal or vehicle metal body. Image courtesy of Diode Dynamics

Connecting the Positive Wire

The other major wire is your positive wire. It is wrapped in a black protective sleeve, but inside you can see it is a red wire with a fuse in line. That inline fuse is an important safety feature, and this wire needs to go to your positive battery terminal. This is going to be the major source of power for everything the relay drives. Because the heavy power runs straight from the battery through the fuse, you get a clean and protected supply to your accessories.

Understanding the Output Wires

The next two wires look similar to each other and these are your output wires. This is simply your power output using a standard DC connector. That means our splitters and all of our accessories will plug right into this, whether it is an RGB multicolor controller, or a single color terminal adapter to plug it right in. It is very versatile, and you can always add splitters to run more things off this one relay. We really like this flexibility because it lets one harness grow with your build over time.

Output wires with DC connector for accessory power
Output wires use a standard DC connector compatible with splitters and accessories. Image courtesy of Diode Dynamics

The Signal Wire: The Heart of the Setup

The final wire is your signal wire, and this is the one that really matters. You need to connect this to a 12 volt signal. There are two different ways to handle it depending on how you want the system to behave.

As you might have already guessed, the O-ring connector on this wire can be connected directly to your battery, making the whole thing plug and play. You would not even need the extra connector. The tradeoff is that this keeps the relay on at all times. That might be perfectly okay if you plan to add a switch later, or if you have a remote control that handles the on and off function instead.

If you do not want it powered all the time directly from the battery, you simply undo that connection. That piece can be discarded if you are not connecting straight to the battery. Instead, the included connector is going to connect right into your parking light wire, or another accessory wire you want your lighting to turn on with. For example, if you want your lighting to come on with the parking lights, the parking light wire is your 12 volt signal source.

Making the Ttap Connection to a Parking Light Wire

For this part, first identify the positive wire coming from your headlight or wherever your parking light power lives. If you want your accessories to come on with the parking lights, this is going to be the wire that is energized when the parking light is on. Place the ttap connector onto that wire, then clamp it down firmly with a pair of pliers or another suitable tool to make a solid connection.

Ttap connector clamped onto parking light wire
A ttap connector clamps onto the parking light wire to create a secure signal connection. Image courtesy of Diode Dynamics

Once the ttap is clamped on, the connector snaps into place and you will see it is nice and secure. All you have done is create a convenient little access point, and now your signal wire can plug directly into it. It is as convenient as that. You can always unplug it later if you need to uninstall the kit or move the wires around. With the parking light wire feeding this signal connection, the relay will send power out to your standard output wires whenever the parking lights are on.

Adding the Optional LED Switch

If you purchased the switch, here is how to add it into the mix. For this method, we assume you want to connect the signal side directly to the battery so that the switch becomes the only thing controlling the accessories. So you put the battery connector wire back on, meaning the relay has a solid, always available battery output ready to go, and the switch decides when that power actually flows.

Take your switch wires and look them over. You will notice there is one shorter wire and one longer wire. Set the shorter wire aside for now. The longer wire is basically a simple double wire. One side has two female connectors, and the other side has a male and a female connector. The two female connectors go into your vehicle cabin where you want to mount the switch, while the male and female side stays in your engine bay.

What we are really doing here is interrupting the signal. Take the signal connection apart (remember it is attached to your battery, so be careful during an actual install), then connect male to female and female to male. As you can see, the signal now routes into your vehicle cabin and back out to the relay, with the switch sitting in the middle of that path.

LED switch wiring with male and female connectors
The LED switch wiring interrupts the signal wire using male and female connectors. Image courtesy of Diode Dynamics

Now take your LED switch and plug it onto the two silver connectors. With the signal coming up to the switch, flipping it on lets the signal continue and turns on the relay. Flipping it off interrupts that signal and the relay shuts off. It is as simple as that.

Wiring the Switch Ground for the LED

The last little wire is the switch ground wire, and this is what makes the LED on the switch itself illuminate. Plug it onto the gold terminal, which is the ground terminal, then ground the other end to any metal bit in your cabin area behind the dash. That allows the LED to light up when the switch is active.

Ground wire connected to gold terminal on LED switch
Connecting the ground wire to the gold terminal allows the switch LED to illuminate. Image courtesy of Diode Dynamics

One handy troubleshooting tip: if the LED stays on all the time instead of flipping with the switch, just swap the two signal wires around on the silver plugs and that will solve the problem. It is a quick fix that trips up a lot of people on their first install.

Choosing the Right Harness for Your Build

This accessory harness is a great match for parking light triggered lighting like halos and demon eyes, but Diode Dynamics offers heavier options when your current demands grow. If you are powering larger off road lighting, the Heavy Duty Dual Output Offroad Harness is worth a look, and the full Stage Series Wire Harness Lineup gives you several configurations to match different light setups.

If you are shopping across brands, we also keep a couple of proven options in our own store. The Relay Wire Harness Kit is a solid universal choice, and for pod lighting builds the LED Pod Power Harness is built to handle multiple pods cleanly. Any of these follow the same core relay principles we covered above, so the skills you learn on one carry straight over to the next.

Final Thoughts

After going through the full process, we think this accessory wiring harness strikes a nice balance between simplicity and flexibility. The relay keeps your accessory power safe and separate from other circuits, the output wires accept splitters and controllers for easy expansion, and the ttap signal connection makes parking light triggering genuinely plug and play. Add the optional LED switch and you get clean manual control with an illuminated indicator. Whether you run it off the parking lights or off the battery with a switch, the install is approachable for a weekend in the garage.

Frequently Asked Questions

What is included with the Diode Dynamics accessory wiring harness?

The kit includes the relay harness itself, one connector, and optional switch wiring with an LED switch in a selected color.

How does the relay in this harness work?

The relay takes a major power source and sends it to connected components when triggered by a smaller 12V signal, such as a parking light wire, providing reliable power without overloading other circuits.

Can the harness be wired directly to the battery without a switch?

Yes, the ground and positive wires can connect directly to the battery for a plug and play setup, but this keeps the relay powered at all times unless a switch or remote is added.

How do you connect the harness to a parking light wire?

A ttap connector is clamped onto the parking light positive wire, which allows the included wire to plug directly into it and snap securely into place.

How does the optional LED switch get wired in?

The switch interrupts the signal wire using a male and female connector setup, with a separate ground wire connecting to the gold terminal so the switch LED illuminates when active.

<!, wp:html , >


Meet the people behind Better Automotive Lighting

John Tobias, Better Automotive Lighting

John Tobias, Headlight Junkie and Industry Veteran
Before managing pricing and product categories for the DLG brands, John worked directly with customers in customer service and tech support, then spent several years in marketing creating content like this and the videos published online. Today he takes more than ten years of aftermarket automotive lighting experience to events all over the USA, meeting customers and talking to real people about what they care about. He is focused on understanding the market, the trends, the big players, and what matters to lighting enthusiasts. John has tested thousands of lights, works directly with lighting engineers to evaluate the technical performance behind every recommendation, and is one of the foremost experts on everything happening in the world of aftermarket automotive lighting. LinkedIn

<!, /wp:html , >